Leave Your Message
How to avoid water seepage defects during on-site installation of aluminium doors

How to avoid water seepage defects during on-site installation of aluminium doors

2026-06-30

Water leaks on aluminum doors and windows? Almost every construction worker has run into this annoying problem. Most people think it’s bad glass or poor door quality that causes leaks. But we’re here to tell you the real reason, based on 20 years of experience at Jiangsu Guoxin Glass Co., Ltd. Over 90% of leaks happen simply because of careless installation. This issue is even more common for doors and windows fitted with insulated glass, laminated glass and fireproof glass. These glass types are delicate, so even tiny mistakes during installation let rainwater seep in. The result? Wet walls, foggy glass, rusty hardware, and your doors and windows break down much faster. Fix these easy installation mistakes, and you’ll rarely deal with leakage again.

Aluminium Door.jpg
Pre-Installation Inspection: Control Frame and Glass Quality From the Source
Want to avoid annoying door and window leaks? It’s actually pretty easy. Just check all your materials before you start installation. Most on-site leaks and reworks are not caused by bad construction work — they’re from bad materials. Never use bent, twisted or uneven aluminum frames. They create uneven gaps that will definitely leak later. Also, spend a few seconds checking your insulated glass, laminated glass and fireproof glass. Make sure insulated glass is well sealed, laminated glass edges don’t peel, and fireproof glass has clean, tight edge sealing. Replace any defective frames or glass early on, and you’ll save a lot of time, money and trouble down the line.


Standardize Frame Fixing and Gap Filling to Prevent Wall Joint Seepage
Wondering why aluminum doors and windows always leak at the wall connection? It’s almost always loose frames and wrong gap filling. When installing, make sure your aluminum frames are flat, straight and firmly fixed — no shaking or wobbling at all. Here’s a must-know tip for every installer: never fill wall gaps with only cement. Cement cracks easily with temperature changes, and buildings shift slightly over time. Those small cracks let water keep seeping in. The correct way is to use soft waterproof filler to fully fill the gaps, then apply high-quality waterproof glue. This simple method works great for all aluminum doors and windows with insulated glass, laminated glass and fireproof glass, keeping them leak-free for years.


Custom Installation Standards for Insulated Glass, Laminated Glass and Fireproof Glass
Here’s a straightforward tip for installers: different glass needs different installation ways. Don’t take shortcuts by installing insulated glass, laminated glass and fireproof glass the exact same rough way. This lazy method always leaves small gaps and causes water leaks. As a professional glass supplier for door and window factories, we’re sharing simple, practical field tips. For insulated glass, spread glue evenly on all edges to block moisture and stop fogging. For laminated glass, protect the edge glue layer during installation to avoid damage and leakage. For fireproof glass on fire-rated doors and windows, seal edges tightly and fix the beads firmly to ensure both fire resistance and waterproof performance. Use the right method for the right glass, and almost all glass-related leaks will disappear.

Aluminium Door1.jpg
Optimize Sealing and Drainage System to Reduce Seepage Rate Fundamentally
Stopping door and window leaks is way simpler than you think. It all comes down to two basic things: tight sealing and unblocked drain holes. After fixing frames and glass securely, seal every tiny gap, including the joints between glass and frame, as well as frame and wall. With all gaps fully sealed, water has no way to get inside. Besides, set drain holes in the right position and keep them clean all the time. Clogged drain holes trap rainwater and cause plenty of unnecessary leaks. With tight sealing and smooth drainage, aluminum doors and windows equipped with insulated glass, laminated glass and fireproof glass will hardly leak, saving you from troublesome after-sales issues.


Post-Installation Water Test and Daily Maintenance for Long-Term Waterproof Performance
Great installation alone isn’t enough to keep your doors and windows from leaking forever. If you want long-term stable waterproof performance, simple post-checks and daily maintenance are necessary. After installing aluminum doors and windows with insulated glass, laminated glass and fireproof glass, run a complete water test to find hidden leaks and fix all issues before project handover. In daily use, just clean drain holes regularly, and check whether your sealant and sealing strips are cracked, aging or worn out. These easy routine checks can prevent most leakage problems and greatly extend the service life of your doors and windows.


Founded in 2006, Jiangsu Guoxin Glass Co., Ltd. has 20 years of professional production and export experience in the glass industry. We mainly supply high-quality insulated glass, laminated glass and fireproof glass, which perfectly match all kinds of aluminum doors and windows. All our glass products are sturdy, waterproof and durable, perfect for various construction projects. We also support customized glass sizes to fit your unique project demands. If you need reliable glass products and professional service, feel free to contact us for free consultation at any time!